Home
  About Us
  Testing Services
   
Chemical Division
Electrical Division
Mechanical Division
Metallurgy Division
  Calibration Services
   
Chemical Division
Electrical Division
Mechanical Division
Metallurgy Division
  Test Charges
   
Chemical Division
Electrical Division
Mechanical Division
Metallurgy Division
  Test charges BIS only
  Right to Information
  Quality Policy
  Training Services
  Job Tracking
  Tenders
  Enquiry
  Contact Us
   
                   

TESTING/CALIBRATION CHARGES
(CHEMICAL DIVISION)
SL. NO.
 Name of the test ISS No. SSI Unit
(Rs.)
 Non-SSI
(Rs.)
TESTING CHARGES EFFECTIVE FROM 01.04.2005
I General      
1. Moisture      
  (a)
(b) 		Karl Fisher/Dean Stark
oven Method 		  600/-
375/- 		 800/-
500/-
2.  Relative Density, Bulk Density, Sp. Gravity   375/-  500/-
3.  Electric Strength (Break down Voltage)    1125/-  1500/-
4. Water absorption, 2&24 hrs.   750/-  1000/-
5. PH   375/-  500/-
6. Flash point   375/- 500/-
7. Boiling Point   375/- 500/-
8. Melting/Softening point   375/- 500/-
9. Viscosity   450/- 600/-
10. Ash   450/- 600/-
11. Total solids   375/- 500/-
12. Nitrogen   375/- 500/-
13. Sieve test   300/- 400/-
14. Assay   750/- 1000/-
15. Hardness, Shore-A   375/- 500/-
16. Distillation range   375/- 500/-
17. Lead Leaching   600/- 800/-
18. Qualitative identification of Plastic, Rubber, Acid & Basic radicals etc.   375/- 500/-
19. Mercurous Nitrate test   375/- 500/-
20. Persulphate test   375/- 500/-
21. Resistance to external influence   375/- 500/-
22. Salt spray test (96 hrs.cycle)   600/- 800/-
23. Ageing test (24 hrs.)   375/-
+(15/- / hrs.)
 500/-
+( 20/- /hrs.)
 
II. BITUMEN & BITUMEN PRODUCTS       
A




 i)



 Cut Back Bitumen
- Flash point
- Solubility in TCE
- Water content
 		 IS:217 375/- 
600/-
600/- 		500/-
800/-
800/-
        1575/- 2100/-
  ii)





  		 Paving/Industrial Bitumen
- Specific gravity
- Penetration
- Softening Point
- Flash Point
- Solubility inT.C.E
- Ductility test 		IS:73/1992702
/1998  		 375/- 
600/-
375/-
375/-
600/-
600/- 		500/- 
800/-
500/-
500/-
800/-
800/-
      2925/-  3900/- 
  iii)



 		 General Tests:
- Flash point
- Solubility in TCE
- Water content
- Ductility test  		   375/-
600/-
600/-
600/- 		500/-
800/-
800/-
800/-  
         
B.  Bitumen Felt/Fibre glass  Bitumen felt IS:7193-94 1322-93 2250/-  3000/- 
1.  Total weight of the finished bitumen felt    225/-  300/- 
2.  Pliability test    450/-  600/- 
3.  Storage sticking test   450/-  600/- 
4.  Heat Resistance test    450/-  600/- 
5.  Water absorption     600/-  800/- 
6  Thickness of core    225/-  300/- 
7  Softening Point    375/-  500/- 
         
C.  Performed fillers for expansion joint IS:1838(Pt.I)-83    
1.  Resistance to Handling    375/-  500/- 
2.  Recovery    450/-  600/- 
3.  Compression    900/-  1200/- 
4.  Extrusion    450/-  600/- 
5.  Water Absorption    375/-  500/- 
6.  Density    375/-  500/- 
7. Bitumen content    450/ 600/- 
         
D. Hot Applied Sealing Compound IS: 1834-84    
  Grade A- Pour Point, Flow & Penetration   1350/-  1800/-
  Grade B- DO- & Aviation Fuel Res.   2700/- 3600/-
 
III

CEMENT/CONCRETE/BRICKS

     
A.

Cement

IS:269, 8112,12269     
1. Setting time   600/- 800/-
2. Soundness (Le-Chetelier)   450/- 600/-
3.

Fineness (Sieving/Blain air permeability)

   450/- 600/-
4. (i) Compressive Strength 3/7 days   1500/- 2000/-
(ii) – do – 28 days     1500/- 2000/-
5.

Chemical analysis of cement

  2250/- 3000/-
6.

Cement concrete/cement mortar analysis (Cement:Sand:Aggregate)

IS:1199 2250/- 3000/-
7.

Compressive strength of cast cylinder/cube (Average of 3)

  600/- 800/-
         
B.

Burnt Clay Bricks,

IS: 1077     
1.

Water absorption

   600/- 800/-
2. Crushing strength (average of 5 bricks)   900/- 1200/-
3. Dimension L, W, H    375/-  500/- 
4. Efflorescence   600/- 800/-
         
C. Water proofing compound, IS:2645     
1. Chloride   375/- 500/-
2. Setting time   600/- 800/-
3.

Comp. Strength 7 days

   1500/- 2000/-
         
D.

Plasticizer (Admixture)  

 IS:9103, Cl.9 /1999     
1. Dry Material Content    375/-  500/- 
2. Ash Content    450/-  600/- 
3. Relative Density    375/-  500/- 
4. pH    375/-  500/- 
IV  CHEMICAL INORGANIC/ORGANIC       
1. Qualitative Test    375/- 500/-
2. Assay    750/- 1000/-
3. Acids, (HC1, HNO3, H2SO4, etc.) IS:264
IS:265
IS:266 		2625/-
 3500/-
4. Other chemicals as per ISS. NaOH,Na2CO3, Ferric alum. Bleaching powder, AgNO3, NaCl, Zinc oxide, Trisodium Phosphat, Hydrazine Hydrate etc.   2625/- 3500/-
 
V COSMETICS/CSD ITEMS
      
1.

Hena powder (Mehandi);  

 IS:11142-84,
IS:7159-84 		2625/- 3500/-
2.

Tooth paste;  

 IS:6356 3000/- 4000/-
3. Tooth powder; IS:5383 2250/- 3000/-
4. Talcom powder, IS:3959 2250/- 3000/-
5.

Shaving cream,

IS:9740 2625/- 3500/-
6.

After shave lotion, (4 Tests)

 IS:9255 1500/- 2000/-
7.

Shampoo,

IS:7884 1500/- 2000/-
8.

Face cream,

IS:6608 1875/- 2500/-
9.

Aggarbatti,

IS:13582 1500/- 2000/-
10

Tooth brush,

IS:3387 2250/- 3000/-
11.

Shaving brush,

IS:4580 1875/- 2500/-
12.  Shaving soap, IS: 5784 1875/-  2500/- 
13.  Tissue Paper Roll IS: 8460    
    Type A   750/- 1000/-
    Type B   1875/- 2500/-
14. Wax Candle IS:11359 2625/- 3500/-
15. Razer Blade   IS:9294 3000/- 4000/-
16. Mach 3 Cartridge IS: 13031 3000/- 4000/-
17.

Mosquito Coil

 IS: 13438 1500/- 2000/-
18.

Mosquito Mat

 IS: 13439 1125/- 1500/-
19. Aluminum Foil TDS 1125/- 1500/-
20. Hair Oil/Baby Oil IS: 7123 2625/- 3500/-
21. Vaseline IS: 9339 1875/- 2500/-
22. Perfume/Deodorent TDS 750/- 1000/-
23. Fabric Bleach TDS 1500/- 2000/-
24. Hair Dye IS: 8481 2288/- 3050/-
25. Soap Case TDS 1125/- 1500/-
26. Naphthalene Ball IS: 539 1875/- 2500/-
27. Toilet Brush TDS 750/- 1000/-
28. Toilet Cleaner TDS 750/- 1000/-
 
VI (A) ELECTROPLATED & ANODISED
COMPONENTS		      
1. Thickness of silver, Nickel, Cadmium, Chromium, Zinc, Lead, Phosphate & Tin plating etc. IS:3203 450/- 600/-
2. Anodic coating/Powder Coat. Thickness IS:1868,6012& 5523 450/- 600/-
3. Uniformity/Dip. Test IS:2633 450/- 600/-
4. Mass of zinc coating ,Lead &Tin Coating etc. IS: 6745, 1327 & 3618 450/- 600/-
5. Adhesion test IS:2629 450/- 600/-
6. Knife test IS:2629 450/- 600/-
         
D GI BARBED WIRE, IS:278    
1. Dimensions/mass   750/- 1000/-
2. Material, (C, S, P) IS:280-1972 1125/- 1500/-
3. Galvanizing Test   1350/- 1800/-
         
VII GREASE & WAXES, OILS & LUBRICANTS      
A) Graphite Grease IS:508-87    
1. Oil extraction from grease   600/- 800/-
2. Kinematic Viscosity   450/- 600/-
3. Flash point   375/- 500/-
         
B) Grease complete as per ISS IS: 506-93    
1. Consistency   375/- 500/-
2. Graphite   375/- 500/-
3. Drop point   375/- 500/-
4. Copper strip corrosion   600/- 800/-
5. Water content   600/- 800/-
6. Free acidity   375/- 500/-
7. Free alkalinity   375/- 500/-
8. Heat stability   450/- 500/-
9. Sulphaled Ash   450/- 600/-
10. Low pumping properties   450/- 600/-
11. Evaporation loss   450/- 600/-
         
Viii METALS & ALLOYS      
1. C,S,P,Mn,Si,Ni,Cr,Cu,V,W,Ti, Cu,Pb,Sn,Fe,Zn,Mg,Al,Ag & As etc   375/- Per element 500/- (Per element)
2. Assay (Lead/Copper/Aluminium) only   750/- 1000/-
3. Chips making/Cutting charges per sample   150/- 200/-
 
ix. LIME STONE/LIME (BUILDING LIME) IS:712-84 &1514-90    
1. Calcium Oxide   375/- 500/-
2. Magnesium Oxide   375/- 500/-
3. Silicon di oxide   375/- 500/-
4. Aluminium di oxide   375/- 500/-
5. Iron Oxide   375/- 500/-
6. Insoluble Residue in acid & alkali   375/- 500/-
7. Moisture Content   375/- 500/-
8. Available Lime   375/- 500/-
9. Carbon di oxide   375/- 500/-
10. Fusion Charge   750/- 1000/-
         
x. PAINTS, VARNISHES & THINNERS      
A) Paints & Varnishes      
1. Drying time IS:101 300/- 400/-
2. Consistency   300/- 400/-
3. Wet opacity   300/- 400/-
4. Colour   300/- 400/-
5. Residue on sieve   300/- 400/-
6. Water content   600/- 800/-
7. Hardness / Flexibility   300/- 400/-
8. Resistance to Bleeding   300/- 400/-
9. Flash point (Abel)   300/- 400/-
10 Mass in kg/10 lit.   300/- 400/-
11. Volatile/Non-Volatile matter   300/- 400/-
12. Resistance to sea water   450/- 600/-
13. Lead restriction/freedom from Lead   450/- 600/-
14. Resistance to chemical (each chemical)   450/- 600/-
15. Resistance to heat   375/- 500/-
16. Resistance to water   265/- 350/-
17. Resistance to wear (6 hrs.)
   600/-
 800/-
- do - (30 hrs.)   1875/- 2500/-
18. Fineness of grinding   375/- 500/-
19. Wet abrasion test   375/- 500/-
20. Resistance to dry rubbing   300/- 400/-
21. Durability (Road marking) 31 days   1125/- 1500/-
22. Water repellency test   450/- 600/-
23. Scratch hardness test   375/- 500/-
24. Gloss (60/45 deg.), Each test   300/- 400/-
25. Wet film thickness   300/- 400/-
26. Impact resistance   375/- 500/-
27. Adhesion / Flexibility test   375/- 500/-
28. Protection against corrosion under condensation condition 7 days   1125/- 1500/-
29. Phthalic anhydride content   600/- 800/-
30. Volume solids   375/- 500/-
31. Accelerated storage stability test (60oC for 96 hrs.)   750/- 1000/-
32. Complete testing of paint, varnish
excluding Fastness to light, Durability, Fire resistance test & Chemical composition. 		IS:1874, 104,158, 341, 524 & 77 etc. 3375/- 4500/-
33. Fastness to light test upto 72 hrs.   1125/- 1500/-
34. -do- upto 100hrs.   1500/- 2000/-
35. Fastness to light test above 72 hrs,each additional cycle of 72 hrs .   1125/-+750/- 1500/-+1000
 
B CEMENT PAINT IS-5410/92 5250/- 7000/-
  (i) Chemical composition   1875/- 2500/-
  (ii) As per table-1   2250/- 3000/-
  (iii) fastness to light, 72 hrs.   1125/- 1500/-
         
C Dry Distemper IS-427&428 3375/- 4500/-
  (i) fastness to light   1125/- 1500/-
  (ii) As per table-1   2250/- 3000/-
         
D Thinner as per IS:1745    
1. Flash point   375/- 500/-
2. Aromatic compounds   600/- 800/-
3. Copper strip corrosion   450/- 600/-
4. Residue on evaporation   450/- 600/-
5. Total as per ISS   2250/- 3000/-
         
E Other paints as per ISS      
1. Enamel paint (under coat), IS:133 4875/- 6500/-
2. R.M. Paint Road Marking, IS:164 4500/- 6000/-
3. R.M. Paint air drying (General) IS:168 3375/- 4500/-
4. R.M. Paint (Lead oxide / Zinc chrome) IS:2074 3375/- 4500/-
5. Syn.Ename; Ext. under coat, IS:2932 3375/- 4500/-
6. Syn. Exterior finishing, including weathering test IS:2933 7500/- 10.000/-
7. R.M. Paint Fin., Interior IS-3537 4500/- 6000/-
8. R.M.PAINT EXT. For ships IS-6951 4500/- 6000/-
9 Plastic Emulsion Paint IS-5411 4500/- 6000/-
         
F Putty for glass/window frames IS-419 3375/- 4500/-
         
G Knifing stopper (Putti), complete requirement Zn-Cr Primer & Grey filler) IS:5083 3375/- 4500/-
 
xi PESTICIDES & INSECTICIDES      
A Chlorpyrifos IS:8944    
1. Active Ingredient (Purity Test)   900/- 1200/-
2 Acidity   375/- 500/-
3. Alkalinity   375/- 500/-
4. Cold Test   375/- 500/-
5. Flash Point   375/- 500/-
6. Emulsion Stability   375/- 500/-
  Complete test   2250/- 2000/-
         
B Insecticidal spray IS:1824, 7872,9665 2250/- 2000/-
         
xii POLISHES      
A Shoe polish paste IS:1746-85 2250/- 3000/-
1. Odour   300/- 400/-
2. Colour   300/- 400/-
3. Consistency   300/- 400/-
4. Applicability   300/- 400/-
5. Colour of Water extract   300/- 400/-
6. Softening Point   300/- 400/-
7. Ash Content   300/- 400/-
8. pH   300/- 400/-
9. Distillation Range   300/- 400/-
10. Non-Volatile Matter   300/- 400/-
11. Flash Point   300/- 400/-
12. Ozze Test   300/- 400/-
         
B Floor Polish IS:8541-77 2250/- 3000/-
C Automobile polish IS:5487-83
5480		 2250/- 3000/-
D Metal polish IS:6271-71
 2250/- 3000/-
E White liquid canvas, (Blanco) IS:10025/81 2250/- 3000/-
         
xiii PLASTICS      
A P.V.C. PIPES      

1.

 

 Effect on water
a) Lead
b) Mercury
c) Cadmium
IS:4985 1125/-
900/-
900/- 		1500/-
1200/-
1200/-
2. Resistance to sulphuric acid (14 days)   1125/- 1500/-
3. Resistance to heat   375/- 500/-
4. Overall migration   1125/- 1500/-
5. Carbon black content   600/- 800/-
6. Identification of PVC, PE etc.   375/- 500/-
7. Glass content   375/- 500/-
8. Sp. Gravity / Water absorption   375/- 500/-
B

 P.V.C. Water Stop
(Effect on Alkali 7 & 28 days) 		Is: 12200 1650/- 2200/-
C Plastic Storage Water Tank
Migration of elements & carbon black 		  1725/- 2300/-
 
xiv RUBBER PRODUCTS      
A)  Natural Rubber Latex, Styrene, Butadiene Rubber       
1. Density / S.G.   375/-  500/-
2. Hardness Test, Shore A   375/-  500/- 
3.
Identification of SBR, Polychloprene, Neoprene, Silicon etc.
   450/- 600/-
4. Volume change   375/-  500/- 
5.  Elastomer Content   1875/-  2500/- 
         
xv SOAPS & DETERGENTS      
A) Laundry Soap IS:285 1875/-  2500/-
1. Total Fatty Matter (TFM)   600/- 800/-
2. Alcohol insoluble   450/- 600/-
3. Unsaponified Fatty matter   450/- 600/-
4. Glycerol   450/- 600/-
5. Rosin Acids   450/- 600/-
6. Titer of total fatty acids   450/- 600/-
7. Free Caustic alkali   375/- 500/-
8. Chlorides, as NaCl   375/- 500/-
9. Moisture Content   375/- 500/-
10. Matter insoluble in alcohol   375/- 500/-
11. LSD/NSD content   375/- 500/-
         
B) Detergent Powder IS: 4955 1500/- 2000/-
1. Active ingredient   600/- 800/-
2. Matter insoluble in water   375/- 500/-
3. PH/ Active alkalinity   375/- 500/-
4. Total Phosphate   375/- 500/-
5. Sieve test   375/- 500/-
         
C) Syn. Detergent Woolen & Silk fabrics IS:9458 1500/- 2000/-
D) Cleaning powder IS:6047 1500/- 2000/-
E) Detergent, house hold (Bar/Cake) IS:8180 1500/- 2000/-
F) Syn. Detergent (Industrial) IS: 4956 1500/- 2000/-
         
G) Acid slurry IS:8401 1500/- 2000/-
1. Clear point   375/- 500/-
2.  Free alkyl benzene   375/-  500/-
3.  Free Sulphuric acid   375/-  500/- 
 
xvi STATIONERY ITEMS      
A) Paper G.S.M., single sheet   225/ 300/-
         
B) Paper Duplicating / Writing / Printing ISS 1060, 1848    
1. G.S.M. /Substance   375/- 500/-
2. Size   225/- 300/-
3. PH Value   375/- 500/-
4. Cobb test   375/- 500/-
5. Bursting strength   375/- 500/-
6. Tensile Index   375/- 500/-
7. Tear Index   375/- 500/-
8. Opacity/Brightness /Gloss   375/- 500/-
9. Folding Endurances   375/- 500/-
         
C) Carbon paper IS:8075, 1551, 3450 1500/- 2000/-
         
D) Computer stationery IS:12766    
1. GSM   225/- 300/-
2. Size each dimension   225/- 300/-
3. Bulk cc/gm   375/- 500/-
4. Moisture content   375/- 500/-
5. Ash   450/- 600/-
6. Cobb test (One min)   375/- 500/-
7. Complete tests as per ISS   1875/- 2500/-
         
E) Office paste IS:2257    
1. Description   150/- 200/-
2. Total solids   375/- 500/-
3. PH   375/- 500/-
4. Adhesive strength   300/- 400/-
5. Brittleness & Moisture absorption   375/- 500/-
6. Stability at 37oC, 13 days   450/- 600/-
7. Consistency   300/- 400/-
8. Complete test as per ISS   2250/- 3000/-
9. Keeping quality after one year   2250/- 3000/-
         
F Pin paper IS:5630-80    
1. Shape and dimensions   225/- 300/-
2. Workmanship and finish   150/- 200/-
3. Corrosion resistance test   450/- 600/-
         
G Photocopier paper IS:14490 1875/- 2500/-
H Stamp Pad IS:4747 750/- 1000/-
I Stamp pad ink IS:393 1200/- 1600/-
J Staples IS:5348 3000/- 4000/-
 
xvii VITREOUS CHINA GLAZED PRODUCT      
A Ceramic Tiles IS:777-88, 17368,13753-56 2175/- 2900/-
1. Water absorption   375/- 500/-
2. Crazing   600/- 800/-
3. Impact strength   450/- 600/-
4. Resistance to chemicals   375/- each 500/- each
         
B Rural Pan IS:771, 2556 5250/- 7000/-
C Chequerd tiles
(except wear & transverse strength)
 IS:1237, 1380 1500/- 2000/-
D Ceramic unglazed vitreous acid resisting tiles/Acid resistance brick IS: 4457-82
IS: 4860		 2500/- 3000/-
         
xviii WATER & EFFLUENTS      
1. Total hardness/total dissolved solids   450/- 600/-
2. Organic Solids   375/- 500/-
3.. In organic solids   375/- 500/-
4. Suspended Matter   375/- 500/-
5. Acidity (Vol. of 0.02N NaOH req.for 100 ml.of sample)   375/- 500/-
6. Alkalinity (Vol. of 0.02 N H2SO4 req. for 100 ml. of sample)   375/- 500/-
7. Chloride   375/- 500/-
8. Sulphates   375/- 500/-
9. Conductivity   375/- 500/-
10. pH   375/- 500/-
11. Water for construction IS:456 (Cl.5.4) 2000 1350/- 1800/-
         
xix WOODEN PRODUCTS      
A) Flush door shutter IS:2202 Pt.1    
1. End immersion test, 16 days   1350/- 1800/-
2. Knife test   375/- 500/-
3. Glue adhesion test
375/- 500/-
4. Complete test for Gr .I & II   2100/- 2800/-
         
B) Paneled door wood      
1. Preservative IS:401-82 600/- 800/-
2. Moisture content IS: 287 375/- 500/-
3. Bulk density   375/- 500/-
 
C) Plywood IS: 303    
1. Moisture   375/- 500/-
2. Dimensions   375/- 500/-
3. Preservative test (Cu-Cr-As) IS:5539 1875/- 2000/-
         
D) Particle Board, M.D.F. Board IS:3087,
IS:12486,
IS:12823,
IS:12406		    
1 Density   375/- 500/-
2. Moisture content   375/- 500/-
3. Water absorption, 2hr / 24hr.   450/- 600/-
4. Swelling due to surface absorption   450/- 600/-
5. Resistance to chemical   375/- 500/-
6. Adhesion of Plies   375/- 500/-
         
E) Veneered Particle Board IS:3097    
1. Density   375/- 500/-
2. Moisture content   375/- 500/-
3. Water absorption   450/- 600/-
4. Water resistance test   450/- 600/-
5. Swelling test   450/- 600/-
6. Total charges for above tests   2100/- 2800/-
         
F) Block Board IS:1659    
1. Resistance to water   450/- 600/-
2. Adhesion of plies   375/- 500/-
         
xx MISCELLANEOUS ITEMS      
A). Battery case IS:1146    
1. Resistance to acid
a) 28 days ageing
b) Determination of Cl, Mn & Fe
c) Change in mass
d) Change in volume
e) Appearance 		  1125/-
1125/-
375/-
375/-
300/- 		1500/-
1500/-
500/-
500/-
400/-
         
B Paint Brush IS:384 1875/- 2500/-
         
C LPG Stove / sole plate,
(Finish test)
 IS:42196/ 366    
1. Thickness of Ni plating   450/- 600/-
2. Thickness of Cr plating   450/- 600/-
3. Corrosion resistance (Salt spray)   600/- 800/-
4. Adhesion test   375/- 500/-
         
D Toys/stuffed; EN:71-88, IS:9873-99    
1 Migration of certain elements
(Sb, As, Ba, Cd, Cr, Pb, Hg, Se)
   3000/- 4000/-
 
E Silver glass mirror, IS:3438-94    
1. Silver coating   375/- 500/-
2. Copper coating   375/- 500/-
3. Salt spray, 120 hrs.   1200/- 1600/-
4. Hot water test   2250/- 3000/-
         
F Pressure cooker IS:2347-95    
1. Chemical composition (Gr. –19000)   3000 + 150
(Cutt. Charges)		 4000 + 200
(cutt charges)
2. Plating Test (Ni & Cr)   900/- 1200/-
3. Rubber Gasket, for Pressure Cooker     3000/-
         
G Calibration      
1 Calibration of Thermometers upto 250oC
(5 point calibration; L/C – Min. 0.1oC		   1050/- 1400/-
         
H MISCELLANEOUS CHARGES      
1. Duplicating test report @ per page   150/- 200/-
2. Chips making charges/Cutting charges per sample   150/- 200/-
3. Postage   30/- 30/-
4. Priority/Urgent charges   Double than normal Double than normal
 
NOTE: SERVICE TAX WILL BE CHARGES EXTRA @ 12.24% ON ABOVE TESTING CHARGES.
 
Copyrights © MSME. All Rights are Reserved.
Design & Developed By : Picinfotec